Last previous edition approved in as D – Adopted as a joint ASTM/ IP standard in 2 For referenced ASTM standards, visit. Test Report of Foaming Characteristic (ASTM. D) and Air Release (ASTM D ). Test Report of Foaming Characteristic (ASTM. D) and Air Release. ASTM D Standard Test Method for Air Release Properties of Hydrocarbon Based Oils. standard by ASTM International, 10/01/ View all product.
|Published (Last):||17 June 2004|
|PDF File Size:||7.14 Mb|
|ePub File Size:||7.54 Mb|
|Price:||Free* [*Free Regsitration Required]|
It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine d34277 applicability of regulatory limitations prior to use.
This is not what you are looking for? If the residence time in the reservoir is too short to allow the air bubbles to rise to the oil surface, a mixture of air and oil will circulate through the lubricating oil system.
Once receive your question, the supplier will answer you as soon as possible. The test vessel should be in a hood, or the air outlet tube should be connected to a vent that removes the vapors. Aeration will switch the direction automatically 4. China vicat apparatus China dissolution apparatus China vacuum filtration apparatus.
NOTE 12—For some applications, the shape of the air release time curve may be required. Request a custom order and have something just for you! Attach the wire to the beam and maintain a distance of 10 6 2 mm between the bottom of the sinker and the bottom of the test vessel.
This may result in an inability to maintain oil pressure particularly with centrifugal pumpsincomplete oil films in bearings and gears, and poor hydraulic system performance or axtm. Care shall be taken to avoid restricting the air path with the thermometer bulb or any adapter used.
Air from a cylinder or a nonpulsating pump may be used. Enter between 20 to 4, characters. Balanced Reflux D427 Point Tester. Use of a pressure relief valve set at 70 kPa 10 psi is recommended. This will be noted if the time for the density to return to the initial?
ASTM D3427 Air release value apparatus
Summary of Test Method 4. The significance of this test method has not been fully established. Warning—Compressed gas under high pressure.
NOTE 2—By agreement between the customer and the laboratory, the oil may be heated at other temperatures. Last previous edition approved in as D — Your comments will receive careful consideration at a meeting of the responsible technical committee,1 which you may attend.
Set the circulating bath to give a specimen temperature within 0. Since some reports were incomplete, this resulted in 48 pairs of replicated data. Interchanged parts may be used so long as the resultant test vessel conforms to the stated dimensions.
In addition, use of a safety shield is recommended. However, the precision at these different temperatures is not known at present. This apparatus measures the time for the entrained air content to fall to the relatively low value of 0. The apparatus is equiped with densimeter. You have seen all photos. NOTE 15—The program was run by six laboratories, using?
Typical questions asked about products Does this product support customization?
Astn apparatus measures the time for the entrained air content to fall to the relatively low value of 0. The significance of this test method has not been fully established.
Build-in air heater, safe and fast Technical parameters 1. Changsha Suny Electronic Technology Limited. NOTE 16—The precision statement was developed using 1. This may result in an inability to maintain oil pressure particularly with centrifugal pumpsincomplete oil? Integrated design with big pressure gauge.
China Air Release Value Apparatus ASTM D – China Air Release Testing, Release Value Apparatus
NOTE 6—Previously, chrome sulfuric acid was used in this procedure. For ready comparison, the above statement is shown in DIN terms in Table 1. Warning—The axtm of glass vessels with glass host? A number in parentheses indicates the year of last reapproval. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? Attach the sinker adtm the beam of the density balance by means of the platinum wire so that the bottom of the sinker is 10 6 2 mm from the bottom of the test vessel.
Originally approved in