Home Business ASTM A513 PDF
Business

ASTM A513 PDF

Learn about ASTM A steel mechanical tubing and Atlas Tube’s manufacturing capabilities regarding this product for OEM applications. CALIFORNIA. Arrow Route. Rancho Cucamonga, CA WWW. ASTM A TUBING SPECIFICATIONS. TOLERANCES. ASTM A/AM: Standard Specification for Electric-Resistance-Welded Carbon and Alloy Steel Mechanical Tubing.

Author: Tugar Takora
Country: Armenia
Language: English (Spanish)
Genre: Art
Published (Last): 23 January 2004
Pages: 432
PDF File Size: 10.68 Mb
ePub File Size: 2.4 Mb
ISBN: 722-8-29547-130-8
Downloads: 62845
Price: Free* [*Free Regsitration Required]
Uploader: Gum

This tolerance applies to the speci? C Where the ellipsis Heat and product analyses shall be made to determine the percentages of chemical elements, to which the steel specimens shall conform to. Destructive Weld Tests S6. Cleanup by Machining S3. Nondestructive Electric Test S8. The purchaser and producer may negotiate special radii.

A — 07 Standard Speci? The values stated in each system may not be exact equivalents; therefore each system shall be used independently of the other. Disposition of rejected tubing shall be a matter of agreement between the manufacturer and the purchaser. Originally approved in Except as allowed in S6. D Round Tubing Outside Diameter, in. For grades of round tubing not shown in Table S5. If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.

Tubing heavier than 16 gage will normally be shipped loose, bundled, or in secured lifts. The twist in square and rectangular tubing may be measured by holding one end of the tubing on a surface plate and noting the height of either corner of the opposite end of same side above the surface plate.

  CIRINA FORDA PDF

Combining values from the two systems may result in non-conformance with the standard. Product and Package Marking These requirements shall not be considered, unless speci?

It is informational only and not an official part of the standard; the full text of the standard itself must be asrm to for its use and application. Disposition of such material shall be a matter for agreement. Any remaining inside diameter?

Since the sections are special, dies and other tools are not held available. A Wall Thickness in.

ASTM A Gr Tube, Size: 1/2 Inch, 3/4 Inch, 1 Inch, 2 Inch, 3 Inch | ID:

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. To determine their availability, the purchaser should contact the producer. Round Tubing Outside Diameter, in. Tubing shall be free of injurious defects and shall have a workmanlike finish. For each additional 10 ft or fraction thereof over 24 ft, an additional allowance should be made of plus or minus 1? Largest Nominal Outside Dimension, in.

Such defects as seams, slivers, pits, laps, etc. The area producing the signal may zstm examined. Such requirements shall be considered under the supplementary or basis of purchase provisions of this speci?

A from the ends of the tubes. Special Smooth Inside Surface S4. Last previous edition approved in as A — 06b. This standard is subject to revision at any time by asfm responsible technical committee and must be reviewed every? The squareness of sides is commonly determined by one of the following methods. Within the text the SI units are shown in brackets.

  KEM 5621 PDF

ASTM A513 Gr 1050 Tube, Size: 1/2 Inch, 3/4 Inch, 1 Inch, 2 Inch, 3 Inch

The radii of corners shall be as given in Table If the results of the mechanical tests do not conform to wstm requirements shown in the table, retests shall be made on additional aztm double the original number selected, each of which x513 conform to the speci?

The types of tubing covered here are: Side leg of square to be equal to tube diameter except minimum length of 1 in. D Flash Controlled to 0. Outside diameter burr to be removed for measurement. Link to Active This link will always route to the current Active version of the standard. A,B Outside Diameter, in. A Wall Thickness 38? Current edition approved March 1, A superscript epsilon e indicates an editorial z513 since the last revision or reapproval.

For welded tubing the notch shall be placed in the weld, if visible. NOTE S1—A lot shall consist of all tubes, before cutting to length, of the same size and wall thickness which are produced from the same heat of steel and, when heat treated, subjected to the same?

Soft conversion applies to other SI measurements.

A Flash Controlled to 0.

Author

admin